If you are facing this error, then chances are you may have installed new hardware or software which is causing the issue. Sometimes installing the latest Windows updates seems to cause this issue but you can’t be sure until you troubleshoot the issue. Now as far as software problems are concerned, these might be the possible reasons as to
why you are facing this error:
- Corrupted BCD information
- System File is damaged.
- Loose or faulty SATA/IDE Cable
- Conflicting 3rd party software
- فيروس أو برنامج ضار
The error which you will get after a reboot will be:
خطأ: Windows failed to start. A recent hardware or software change might have caused the issue after you install Windows Updates
The main problem is that you won’t boot into Windows and you will be stuck at this error message screen. In short, you will be inside a reboot loop as every time you restart your PC you will again face the same error message until you fix the issue. So without wasting any time let’s see how actually to Fix “Windows failed to start. A recent hardware or software change might be the cause” with the below-listed troubleshooting steps.
Fix Windows failed to start. A recent hardware or software change might be the cause.
الطريقة الرابعة: تشغيل بدء التشغيل / الإصلاح التلقائي
1. أدخل ملف قرص DVD أو قرص الاسترداد القابل للتمهيد لنظام التشغيل Windows 10 وإعادة تشغيل جهاز الكمبيوتر الخاص بك.
2. When prompted to Press any key to boot from CD or DVD, اضغط على أي مفتاح للمتابعة.
3. حدد تفضيلات اللغة الخاصة بك، ثم انقر فوق التالي. انقر فوق إصلاح جهاز الكمبيوتر الخاص بك في أسفل اليسار.
4. في شاشة تحديد خيار، انقر فوق استكشاف.
5. في شاشة استكشاف الأخطاء وإصلاحها، انقر فوق خيار متقدم.
6. في شاشة الخيارات المتقدمة، انقر فوق الإصلاح التلقائي أو إصلاح بدء التشغيل.
7. Wait till the Windows Automatic/Startup Repairs complete.
8. أعد التشغيل وقد نجحت حل Windows failed to start. A recent hardware or software change might be the causeإذا لم يكن الأمر كذلك، استمر.
اقرأ أيضا: كيفية إصلاح الإصلاح التلقائي لم يتمكن من إصلاح جهاز الكمبيوتر الخاص بك.
Method 2: Boot into Last Known Good Configuration
Before going any further let’s discuss how to Enable Legacy Advanced Boot Menu so that you can easily get Boot Options:
1. Restart your Windows 10.
2. As the system restarts enter into BIOS setup and configure your PC to boot from CD/DVD.
3. أدخل قرص DVD القابل للتشغيل لنظام التشغيل Windows 10 وأعد تشغيل جهاز الكمبيوتر الخاص بك.
4. عندما يُطلب منك الضغط على أي مفتاح للتمهيد من القرص المضغوط أو قرص DVD، اضغط على أي مفتاح للمتابعة.
5. حدد الخاص بك تفضيلات اللغة، وانقر فوق التالي. انقر فوق إصلاح جهاز الكمبيوتر الخاص بك في أسفل اليسار.
6. في شاشة تحديد خيار، انقر فوق استكشاف.
7. في شاشة استكشاف الأخطاء وإصلاحها، انقر فوق خيار متقدم.
8. On Advanced options screen, click موجه الأوامر.
9. When the Command Prompt(CMD) open type C: وضرب الدخول.
10. الآن اكتب الأمر التالي:
BCDEDIT / مجموعة {الافتراضي} إرث BOOTMENUPOLICY
11. واضغط على زر الإدخال إلى تمكين قائمة التمهيد القديمة المتقدمة.
12. Close Command Prompt and back on the Choose an option screen, click Continue to restart Windows 10.
13. Finally, don’t forget to eject your Windows 10 installation DVD to get Boot options.
14. On the Boot Options screen, choose “آخر تكوين جيد معروف متقدمة)."
الطريقة 3: قم بإجراء استعادة النظام
1. أدخل وسائط تثبيت Windows أو محرك الاسترداد/قرص إصلاح النظام وحدد lتفضيلات اللغة، ثم انقر فوق التالي
2. انقر إصلاح جهاز الكمبيوتر الخاص بك في الأسفل.
3. الآن ، اختر استكشاف وثم خيارات متقدمة.
4. أخيرًا ، انقر فوق "استعادة النظام"واتبع التعليمات التي تظهر على الشاشة لإكمال عملية الاستعادة.
5. Restart your PC to save changes and see if you can fix Windows failed to start. A recent hardware or software change might be the cause error.
الطريقة السادسة: تشغيل SFC وCHKDSK
1. Again go to command prompt using the method 1, click on command prompt in the Advanced options screen.
2. اكتب الأمر التالي في cmd ثم اضغط على زر الإدخال بعد كل أمر:
sfc /scannow /offbootdir=c: /offwindir=c:windows chkdsk C: /f /r /x
Note: Make sure you use the drive letter where Windows is currently installed. Also in the above command C: is the drive on which we want to check disk, /f stands for a flag which chkdsk the permission to fix any errors associated with the drive, /r let chkdsk search for bad sectors and perform recovery and /x instructs the check disk to dismount the drive before beginning the process.
3. Exit the command prompt and restart your PC.
Method 5: Rebuild BCD configuration
1. Using above method open command prompt using Windows installation disk.
2. Now type the following commands one by one and hit enter after each one:
bootrec.exe /FixMbr bootrec.exe /FixBoot bootrec.exe /RebuildBcd
3. If the above command fails, then enter the following commands in cmd:
bcdedit /export C:BCD_Backup c: cd boot attrib bcd -s -h -r ren c:bootbcd bcd.old bootrec /RebuildBcd
4. Finally, exit the cmd and restart your Windows.
5. This method seems to Fix Windows failed to start. A recent hardware or software change might cause the error, but if it doesn’t work for you, then continue.
الطريقة الأولى: تعيين ترتيب التمهيد الصحيح
1. When your computer starts (Before the boot screen or the error screen), repeatedly press Delete or F1 or F2 key (Depending upon your computer’s manufacturer) to أدخل إعداد BIOS.
2. Once you are in BIOS setup, select the Boot tab from the list of options.
3. Now make sure that the computer القرص الصلب أو SSD is set as a top priority in the Boot order. If not, use up or down arrow keys to set hard disk at the top, which means the computer will first boot from it rather than any other source.
4. Finally, press F10 to save this change and exit.
أوصى:
هذا كل ما لديك بنجاح Fix Windows failed to start. A recent hardware or software change might be the cause, but if you still have any questions regarding this post, please ask them in the comment’s section.