If you are facing this error, then chances are you may have installed new hardware or software which is causing the issue. Sometimes installing the latest Windows updates seems to cause this issue but you can’t be sure until you troubleshoot the issue. Now as far as software problems are concerned, these might be the possible reasons as to
why you are facing this error:
- Corrupted BCD information
- System File is damaged.
- Loose or faulty SATA/IDE Cable
- Conflicting 3rd party software
- Virus və ya zərərli proqram
The error which you will get after a reboot will be:
Error: Windows failed to start. A recent hardware or software change might have caused the issue after you install Windows Updates
The main problem is that you won’t boot into Windows and you will be stuck at this error message screen. In short, you will be inside a reboot loop as every time you restart your PC you will again face the same error message until you fix the issue. So without wasting any time let’s see how actually to Fix “Windows failed to start. A recent hardware or software change might be the cause” with the below-listed troubleshooting steps.
Fix Windows failed to start. A recent hardware or software change might be the cause.
Metod 1: Başlanğıc/Avtomatik Təmiri işə salın
1. Daxil edin Windows 10 yüklənə bilən quraşdırma DVD və ya Bərpa Diski və PC'nizi yenidən başladın.
2. CD və ya DVD-dən yükləmək üçün hər hansı düyməyə basmaq istənildikdə, istənilən düyməni basın davam edir.
3. Dil seçimlərinizi seçin və Next düyməsini basın. Təmir et klikləyin kompüterinizin sol alt hissəsində.
4. Seçim ekranında üzərinə klikləyin Troubleshoot.
5. Problemin həlli ekranında üzərinə klikləyin Qabaqcıl seçim.
6. Qabaqcıl seçimlər ekranında klikləyin Avtomatik Təmir və ya Başlanğıc Təmiri.
7. Wait till the Windows Automatic/Startup Repairs complete.
8. Yenidən başladın və müvəffəqiyyətlə əldə etdiniz Fix Windows failed to start. A recent hardware or software change might be the cause, deyilsə, davam edin.
Həm də oxuyun: Avtomatik Təmir kompüterinizi təmir edə bilmədiyi necə düzəltmək olar.
Method 2: Boot into Last Known Good Configuration
Before going any further let’s discuss how to Enable Legacy Advanced Boot Menu so that you can easily get Boot Options:
1. Restart your Windows 10.
2. As the system restarts enter into BIOS setup and configure your PC to boot from CD/DVD.
3. Windows 10 yüklənə bilən quraşdırma DVD-sini daxil edin və kompüterinizi yenidən başladın.
4. CD və ya DVD-dən yükləmək üçün istənilən düyməyə basın tələb edildikdə, davam etmək üçün istənilən düyməni basın.
5. Özünüzü seçin dil üstünlükləri, və İleri düyməsini vurun. Təmir et klikləyin kompüterinizin sol alt hissəsində.
6. Seçim ekranında üzərinə klikləyin Troubleshoot.
7. Problemin həlli ekranında üzərinə klikləyin Qabaqcıl seçim.
8. Qabaqcıl seçimlər ekranında klikləyin Command Prompt.
9. When the Command Prompt(CMD) open type C: daxil edin.
10. Now type the following command:
BCDEDIT /SET {DEFAULT} BOOTMENUPOLICY MİRAS
11. And hit enter to Legacy Advanced Boot Menyu aktivləşdirin.
12. Close Command Prompt and back on the Choose an option screen, click Continue to restart Windows 10.
13. Finally, don’t forget to eject your Windows 10 installation DVD to get Boot options.
14. On the Boot Options screen, choose “Last Known Good Configuration (Advanced)."
Metod 3: Sistemin bərpasını həyata keçirin
1. Windows quraşdırma mediasını və ya Bərpa Diski/Sistem Təmir Diskini daxil edin və l seçin.dil üstünlükləri, və Next klikləyin
2. klik təmir kompüterinizin altındadır.
3. İndi seçin Troubleshoot və sonra Təkmilləşmiş Seçimlər.
4. Nəhayət, " üzərinə klikləyin.Sistem bərpa” seçin və bərpanı başa çatdırmaq üçün ekrandakı təlimatlara əməl edin.
5. Restart your PC to save changes and see if you can fix Windows failed to start. A recent hardware or software change might be the cause error.
Metod 4: SFC və CHKDSK-ni işə salın
1. Again go to command prompt using the method 1, click on command prompt in the Advanced options screen.
2. Cmd-də aşağıdakı əmri yazın və hər birindən sonra enter düyməsini basın:
sfc /scannow /offbootdir=c: /offwindir=c:windows chkdsk C: /f /r /x
Note: Make sure you use the drive letter where Windows is currently installed. Also in the above command C: is the drive on which we want to check disk, /f stands for a flag which chkdsk the permission to fix any errors associated with the drive, /r let chkdsk search for bad sectors and perform recovery and /x instructs the check disk to dismount the drive before beginning the process.
3. Exit the command prompt and restart your PC.
Method 5: Rebuild BCD configuration
1. Using above method open command prompt using Windows installation disk.
2. Now type the following commands one by one and hit enter after each one:
bootrec.exe /FixMbr bootrec.exe /FixBoot bootrec.exe /RebuildBcd
3. If the above command fails, then enter the following commands in cmd:
bcdedit /export C:BCD_Backup c: cd boot attrib bcd -s -h -r ren c:bootbcd bcd.old bootrec /RebuildBcd
4. Finally, exit the cmd and restart your Windows.
5. This method seems to Fix Windows failed to start. A recent hardware or software change might cause the error, but if it doesn’t work for you, then continue.
Metod 6: Düzgün yükləmə sırasını təyin edin
1. When your computer starts (Before the boot screen or the error screen), repeatedly press Delete or F1 or F2 key (Depending upon your computer’s manufacturer) to BIOS quraşdırmasına daxil olun.
2. Once you are in BIOS setup, select the Boot tab from the list of options.
3. Now make sure that the computer Sərt disk və ya SSD is set as a top priority in the Boot order. If not, use up or down arrow keys to set hard disk at the top, which means the computer will first boot from it rather than any other source.
4. Finally, press F10 to save this change and exit.
Tövsiyə edilir:
Uğurla əldə etdiyiniz budur Fix Windows failed to start. A recent hardware or software change might be the cause, but if you still have any questions regarding this post, please ask them in the comment’s section.