Reboot and Select Proper Boot Device Issue [SOLVED]: This error is caused because of corrupted system files, incorrect boot order or hard disk failure. These are just some common causes due to which this error is caused in Windows. This error comes up when you boot your Windows and even if you restart your computer you won’t be able to boot as you will be faced with a black screen with error message:
Genstart og vælg korrekt Boot device
Or Insert Boot Media in Selected Boot device and press a key
In some cases even replacing the faulty hard disk doesn’t seem to fix the problem but don’t worry here at troubleshooter, we have listed few possible solutions which will help you troubleshoot this issue easily.
Reboot and Select Proper Boot Device Issue [SOLVED]
Method 1: Set Correct Boot Order
Du ser muligvis fejlen "Genstart og vælg korrekt Boot device” because the boot order is not properly set which means that computer is trying to boot from another source which doesn’t have an operating system thus failing to do so. In order to fix this issue, you need to set the Hard Disk as the top priority in the Boot order. Let’s see how to set proper boot order:
1. Når din computer starter (før startskærmen eller fejlskærmen), skal du gentagne gange trykke på Delete eller F1- eller F2-tasten (afhængigt af din computers producent) for at enter BIOS setup.
2. Når du er i BIOS-opsætning, vælg fanen Boot fra listen over muligheder.
3.Sørg nu for, at computeren Harddisk eller SSD er sat som en topprioritet i Boot-rækkefølgen. Hvis ikke, så brug op eller ned piletasterne til at indstille harddisken øverst, hvilket betyder, at computeren først starter fra den i stedet for nogen anden kilde.
4.Tryk til sidst på F10 for at gemme denne ændring og afslutte. Dette skal have Fix Reboot and Select Proper Boot Device Issue, hvis ikke så fortsæt.
Method 2: Check if the Hard Disk is damaged/failed
If the above method weren’t helpful at all then there is a chance that your hard disk might be damaged or corrupted. In any case, you need to replace your previous HDD or SSD with a new one and install Windows again. But before running to any conclusion, you must run a Diagnostic tool to check if you really need to replace HDD/SSD.
For at køre Diagnostics genstart din pc, og når computeren starter (før startskærmen), skal du trykke på F12-tasten, og når Boot-menuen vises, skal du fremhæve indstillingen Boot to Utility Partition eller Diagnostics-indstillingen og trykke på enter for at starte Diagnostics. Dette vil automatisk kontrollere al hardwaren på dit system og vil rapportere tilbage, hvis der findes et problem.
Anbefalet: Fix Bad Sector issues with HDD using Hiren’s Boot
Method 3: Check if Hard Disk is properly connected
In 50% of the cases, this problem is caused because of the faulty or loose connection of hard disk and to make sure that this is not the case here you need to check your PC for any type of fault in the connection.
Vigtig: It is not recommended to open the casing of your PC if it’s under warranty as it will void your warranty, a better approach, in this case, will be taking your PC in the service center. Also, if you don’t have any technical knowledge then don’t mess with the PC and make sure to look for an expert technician which can help you in checking for faulty or loose connection of hard disk.
Once you have checked the proper connection of hard disk is established, reboot your PC and this time you may be able to Fix Reboot and Select Proper Boot Device Issue.
Method 4: Run startup/Automatic Repair
1. Indsæt den startbare installations-dvd med Windows 10, og genstart din pc.
2. Når du bliver bedt om at trykke på en vilkårlig tast for at starte fra cd eller dvd, skal du trykke på en vilkårlig tast for at fortsætte.
3.Select your language preferences, and click Next. Click Repair your computer in the bottom-left.
4.On choose an option screen, click Troubleshoot.
5.On Troubleshoot screen, click Advanced option.
6.On the Advanced options screen, click Automatic Repair or Startup Repair.
7.Wait til the Windows Automatic/Startup Repairs complete.
8. Genstart, og du har succes Fix Reboot and Select Proper Boot Device issue, if not, continue.
Læs også Sådan repareres Automatisk reparation kunne ikke reparere din pc.
Method 5: Enable UEFI Boot
1. Genstart din pc og tryk på F2 eller DEL afhængigt af din pc for at åbne Boot Setup.
2.The make the following changes:
Change Boot list option to UEFI Disable Load Legacy option ROM Enable Secure boot
3.Next, tap F10 to Save and Exit the boot setup.
Method 6: Change the Active Partition in Windows
1.Again open cmd using Windows installation disk.
2.Type the following command into cmd and hit enter after each one:
Bemærk: Marker altid System Reserved Partition (generelt 100mb) aktiv, og hvis du ikke har en System Reserved Partition, så marker C: Drive som den aktive partition.
DiskPart list disk select disk 0 list partition select partition 1 active exit
3.Close the command prompt and restart your PC. In many cases, this method was able to Fix Reboot and Select Proper Boot Device issue.
Also, see How to fix BOOTMGR is missing Windows 10
Metode 7: Reparation Installer Windows 10
If none of the above solution work for you then you can be sure that your HDD is fine but you may be seeing the error “Reboot and Select proper Boot device Or Insert Boot Media in Selected Boot device and press a key” because the operating system or the BCD information on the HDD was somehow erased. Well, in this case, you can try to Repair install Windows but if this also fails then the only solution left is to Install a new copy of Windows (Clean Install).
Det er det du har med succes Fix Reboot and Select proper Boot device issue men hvis du stadig har spørgsmål vedrørende dette indlæg, er du velkommen til at stille dem i kommentarfeltet.