If you are facing this error, then chances are you may have installed new hardware or software which is causing the issue. Sometimes installing the latest Windows updates seems to cause this issue but you can’t be sure until you troubleshoot the issue. Now as far as software problems are concerned, these might be the possible reasons as to
why you are facing this error:
- Corrupted BCD information
- System File is damaged.
- Loose or faulty SATA/IDE Cable
- Conflicting 3rd party software
- Viruso aŭ malware
The error which you will get after a reboot will be:
Eraro: Windows failed to start. A recent hardware or software change might have caused the issue after you install Windows Updates
The main problem is that you won’t boot into Windows and you will be stuck at this error message screen. In short, you will be inside a reboot loop as every time you restart your PC you will again face the same error message until you fix the issue. So without wasting any time let’s see how actually to Fix “Windows failed to start. A recent hardware or software change might be the cause” with the below-listed troubleshooting steps.
Fix Windows failed to start. A recent hardware or software change might be the cause.
Method 1: Run Startup/Automatic Repair
1. Enmetu la Windows 10 startebla instala DVD aŭ Reakira Disko kaj rekomencu vian komputilon.
2. Kiam oni petas Premu ajnan klavon por ekŝalti de KD aŭ DVD, premu ajnan klavon Por daŭrigi.
3. Elektu viajn lingvopreferojn, kaj alklaku Sekva. Alklaku Ripari via komputilo maldekstre malsupre.
4. Sur elektu opcion ekrano, klaku Problemoj.
5. Sur Troubleshoot ekrano, alklaku la Altnivela opcio.
6. Sur la Altnivelaj opcioj ekrano, klaku Aŭtomata Riparo aŭ Komenca Riparo.
7. Wait till the Windows Automatic/Startup Repairs complete.
8. Rekomencu kaj vi sukcese Fix Windows failed to start. A recent hardware or software change might be the cause, if not, continue.
Ankaŭ Legu: Kiel ripari Aŭtomata Riparo ne povis ripari vian komputilon.
Method 2: Boot into Last Known Good Configuration
Before going any further let’s discuss how to Enable Legacy Advanced Boot Menu so that you can easily get Boot Options:
1. Restart your Windows 10.
2. As the system restarts enter into BIOS setup and configure your PC to boot from CD/DVD.
3. Enmetu la Windows 10 startebla instala DVD kaj rekomencu vian komputilon.
4. Kiam oni petas Premu ajnan klavon por ekfunkciigi de KD aŭ DVD, premu ajnan klavon por daŭrigi.
5. Elektu vian lingvaj preferoj, kaj alklaku Sekva. Alklaku Ripari via komputilo maldekstre malsupre.
6. Sur elektu opcion ekrano, klaku Problemo.
7. Sur Troubleshoot ekrano, alklaku la Altnivela opcio.
8. Sur Altnivelaj opcioj ekrano, klaku komando Prompt.
9. When the Command Prompt(CMD) open type C: kaj batis eniri.
10. Nun tajpu la jenan komandon:
BCDEDIT /SET {DEFAULT} BOOTMENUPOLICY LEGACY
11. And hit enter to Enable Legacy Advanced Boot Menu.
12. Close Command Prompt and back on the Choose an option screen, click Continue to restart Windows 10.
13. Finally, don’t forget to eject your Windows 10 installation DVD to get Boot options.
14. On the Boot Options screen, choose “Last Known Good Configuration (Advanced)."
Metodo 3: Faru Sisteman Restarigon
1. Enmetu la Vindozan instalan amaskomunikilaron aŭ Recovery Drive/System Repair Disko kaj elektu vian llingvaj preferoj, kaj alklaku Poste
2. Klako riparo via komputilo ĉe la malsupro.
3. Nun elektu Problemo kaj tiam Altnivelaj Opcioj.
4. Fine, alklaku "Sistemo Restarigi” kaj sekvu surekranajn instrukciojn por kompletigi la restarigon.
5. Restart your PC to save changes and see if you can fix Windows failed to start. A recent hardware or software change might be the cause error.
Metodo 4: Rulu SFC kaj CHKDSK
1. Again go to command prompt using the method 1, click on command prompt in the Advanced options screen.
2. Tajpu la jenan komandon en cmd kaj premu enen post ĉiu:
sfc /scannow /offbootdir=c: /offwindir=c:windows chkdsk C: /f /r /x
Note: Make sure you use the drive letter where Windows is currently installed. Also in the above command C: is the drive on which we want to check disk, /f stands for a flag which chkdsk the permission to fix any errors associated with the drive, /r let chkdsk search for bad sectors and perform recovery and /x instructs the check disk to dismount the drive before beginning the process.
3. Exit the command prompt and restart your PC.
Method 5: Rebuild BCD configuration
1. Using above method open command prompt using Windows installation disk.
2. Now type the following commands one by one and hit enter after each one:
bootrec.exe /FixMbr bootrec.exe /FixBoot bootrec.exe /RebuildBcd
3. If the above command fails, then enter the following commands in cmd:
bcdedit /export C:BCD_Backup c: cd boot attrib bcd -s -h -r ren c:bootbcd bcd.old bootrec /RebuildBcd
4. Finally, exit the cmd and restart your Windows.
5. This method seems to Fix Windows failed to start. A recent hardware or software change might cause the error, but if it doesn’t work for you, then continue.
Method 6: Set Correct Boot Order
1. When your computer starts (Before the boot screen or the error screen), repeatedly press Delete or F1 or F2 key (Depending upon your computer’s manufacturer) to eniru BIOS-agordon.
2. Once you are in BIOS setup, select the Boot tab from the list of options.
3. Now make sure that the computer Malmola disko aŭ SSD is set as a top priority in the Boot order. If not, use up or down arrow keys to set hard disk at the top, which means the computer will first boot from it rather than any other source.
4. Finally, press F10 to save this change and exit.
rekomendita:
Tion vi sukcese havas Fix Windows failed to start. A recent hardware or software change might be the cause, but if you still have any questions regarding this post, please ask them in the comment’s section.