If you are facing this error, then chances are you may have installed new hardware or software which is causing the issue. Sometimes installing the latest Windows updates seems to cause this issue but you can’t be sure until you troubleshoot the issue. Now as far as software problems are concerned, these might be the possible reasons as to
why you are facing this error:
- Corrupted BCD information
- System File is damaged.
- Loose or faulty SATA/IDE Cable
- Conflicting 3rd party software
- Viris oswa malveyan
The error which you will get after a reboot will be:
Erè: Windows failed to start. A recent hardware or software change might have caused the issue after you install Windows Updates
The main problem is that you won’t boot into Windows and you will be stuck at this error message screen. In short, you will be inside a reboot loop as every time you restart your PC you will again face the same error message until you fix the issue. So without wasting any time let’s see how actually to Fix “Windows failed to start. A recent hardware or software change might be the cause” with the below-listed troubleshooting steps.
Fix Windows failed to start. A recent hardware or software change might be the cause.
Method 1: Run Startup/Automatic Repair
1. Mete la Windows 10 DVD enstalasyon demaraj oswa Disk Recovery ak rekòmanse PC ou.
2. Lè yo mande pou peze nenpòt kle pou demaraj soti nan CD oswa DVD, peze nenpòt kle yo ka kontinye.
3. Chwazi preferans lang ou, epi klike sou Next. Klike sou Reparasyon òdinatè w lan nan anba-gòch la.
4. Sou chwazi yon ekran opsyon, klike sou Rézoudr.
5. Sou ekran depanaj, klike sou la Opsyon avanse.
6. Sou ekran Opsyon Avanse a, klike sou Reparasyon otomatik oswa reparasyon demaraj.
7. Wait till the Windows Automatic/Startup Repairs complete.
8. rekòmanse epi ou gen siksè Ranje Windows failed to start. A recent hardware or software change might be the cause, si ou pa, kontinye.
Epitou Li: Ki jan yo ranje Reparasyon Otomatik pa t 'kapab repare PC ou.
Method 2: Boot into Last Known Good Configuration
Before going any further let’s discuss how to Enable Legacy Advanced Boot Menu so that you can easily get Boot Options:
1. Restart your Windows 10.
2. As the system restarts enter into BIOS setup and configure your PC to boot from CD/DVD.
3. Mete DVD enstalasyon demaraj Windows 10 la epi rekòmanse PC ou.
4. Lè yo mande pou peze nenpòt kle pou demaraj soti nan CD oswa DVD, peze nenpòt kle pou kontinye.
5. Chwazi ou preferans lang, epi klike sou Next. Klike sou Reparasyon òdinatè w lan nan anba-gòch la.
6. Sou chwazi yon ekran opsyon, klike sou Rézoudr.
7. Sou ekran depanaj, klike sou la Opsyon avanse.
8. Sou ekran opsyon avanse, klike sou Kòmand rapid.
9. When the Command Prompt(CMD) open type C: epi frape antre.
10. Koulye a, tape lòd sa a:
BCDEDIT /SET {DEFAULT} BOOTMENUPOLICY LEGACY
11. Epi frape antre nan Pèmèt Legacy Advanced Boot Menu.
12. Close Command Prompt and back on the Choose an option screen, click Continue to restart Windows 10.
13. Finally, don’t forget to eject your Windows 10 installation DVD to get Boot options.
14. On the Boot Options screen, choose “Last Known Good Configuration (Advanced)."
Method 3: Perform a System Restore
1. mete nan fennèt enstalasyon medya oubyen gerizon lecteur/sistèm reparasyon ni plak zo rèldo epi chwazi l oupreferans lang, epi klike sou Next
2. Klike sou Reparasyon òdinatè w lan nan pati anba a.
3. Koulye a, chwazi Rézoudr ak Lè sa a, Opsyon avanse.
4. Finalman, klike sou "Sistèm Renmèt” epi swiv enstriksyon ki sou ekran pou konplete restorasyon an.
5. Restart your PC to save changes and see if you can fix Windows failed to start. A recent hardware or software change might be the cause error.
Metòd 4: Kouri SFC ak CHKDSK
1. Again go to command prompt using the method 1, click on command prompt in the Advanced options screen.
2. Tape lòd sa a nan cmd epi frape antre apre chak youn:
sfc /scannow /offbootdir=c: /offwindir=c:windows chkdsk C: /f /r /x
Note: Make sure you use the drive letter where Windows is currently installed. Also in the above command C: is the drive on which we want to check disk, /f stands for a flag which chkdsk the permission to fix any errors associated with the drive, /r let chkdsk search for bad sectors and perform recovery and /x instructs the check disk to dismount the drive before beginning the process.
3. Exit the command prompt and restart your PC.
Method 5: Rebuild BCD configuration
1. Using above method open command prompt using Windows installation disk.
2. Now type the following commands one by one and hit enter after each one:
bootrec.exe /FixMbr bootrec.exe /FixBoot bootrec.exe /RebuildBcd
3. If the above command fails, then enter the following commands in cmd:
bcdedit /export C:BCD_Backup c: cd boot attrib bcd -s -h -r ren c:bootbcd bcd.old bootrec /RebuildBcd
4. Finally, exit the cmd and restart your Windows.
5. This method seems to Fix Windows failed to start. A recent hardware or software change might cause the error, but if it doesn’t work for you, then continue.
Metòd 6: Mete lòd bòt kòrèk
1. When your computer starts (Before the boot screen or the error screen), repeatedly press Delete or F1 or F2 key (Depending upon your computer’s manufacturer) to antre nan konfigirasyon BIOS.
2. Once you are in BIOS setup, select the Boot tab from the list of options.
3. Now make sure that the computer Disk di oswa SSD is set as a top priority in the Boot order. If not, use up or down arrow keys to set hard disk at the top, which means the computer will first boot from it rather than any other source.
4. Finally, press F10 to save this change and exit.
Rekòmande:
Se sa ou genyen avèk siksè Fix Windows failed to start. A recent hardware or software change might be the cause, but if you still have any questions regarding this post, please ask them in the comment’s section.