If you don’t see Wireless Adapter under Network Connections neither there is a Network adapter tab under device manager then it seems like your Network Adapter is missing or not detected on your Windows 10 which is a serious issue because you won’t be able to access the Internet until the issue is resolved. In short, when you click on the Wireless icon on the system tray there won’t be any device listed in order to connect to the Internet and if you open Device Manager then you won’t see the Network Adapter tab.
These are the reasons behind the Network Adapter missing issue:
- Network adapter missing in Device manager
- No Network Adapters showing in Device Manager
- Network Adapter Not Detected
- Network Adapter Not Found Windows 10
- No Network Adapter In Device Manager
The main cause of this issue seems to be outdated, incompatible or corrupted Network Adapter drivers. If you have recently upgraded from previous versions of Windows then it’s possible that the old drivers will not work with the new Windows and hence the issue. So without wasting any time let’s see how to actually Fix Network Adapter Missing in Windows 10 issue with the below-listed troubleshooting steps.
Note: Just make sure to uninstall any VPN software on your PC before continuing.
Fix Network Adapter Missing in Windows 10
Assicurati di creare un punto di ripristino nel caso in cui qualcosa vada storto.
Method 1: Reboot your Computer
Most of us know about this very basic trick. Rebooting your computer can sometimes fix any software conflict by giving it a fresh start. So if you are someone who would rather put their computer on sleep, restarting your computer is a good idea.
1. Clicca sul menu di avvio e poi clicca sul pulsante di alimentazione disponibile nell'angolo in basso a sinistra.
2. Successivamente, fare clic su Ricomincia opzione e il computer si riavvierà automaticamente.
Dopo il riavvio del computer, controlla se il problema è stato risolto o meno.
Method 2: Flush DNS and Reset Winsock Components
1. Open elevated Command Prompt.
2. Ora digita il seguente comando e premi Invio dopo ciascuno:
ipconfig / release ipconfig / flushdns ipconfig / renew
3. Again open Command Prompt and type the following command one by one and hit enter after each one:
ipconfig /flushdns nbtstat –r netsh int ip reset netsh winsock reset
4. Riavviare per applicare le modifiche. Sembra che lo svuotamento del DNS funzioni Fix Network Adapter Driver Issues on Windows 10.
Method 3: Run WWAN AutoConfig Service
1. Premi il tasto Windows + R quindi digita services.msc e premi Invio.
2. Trova WWAN AutoConfig Service in the list (press W to reach to the end of the list quickly).
3. Fare doppio clic su WWAN AutoConfig Service.
4. If the service is already running then click on Stop, then from the Startup type drop-down select Automatico.
5. Click Apply followed by OK.
6. Fare clic con il tasto destro del mouse su WWAN AutoConfig Service e seleziona Inizio.
Metodo 4: aggiornare i driver della scheda di rete
1. Premi il tasto Windows + R e digita "devmgmt.msc” in Run dialogue box to open gestore dispositivi.
2. Espandi schede di rete, quindi fai clic con il pulsante destro del mouse sul tuo Controllore Wi-Fi (ad esempio Broadcom o Intel) e selezionare Aggiorna software driver.
3. Ora seleziona "Search for automatically for updated driver software".
4. Adesso Windows will automatically search for the Network driver update and if new update is found, it will automatically download and install it.
5. Once finished, close everything and reboot your PC.
6. If you’re still facing the Network Adapter Missing in Windows 10 issue, then again right-click on your WiFi controller and select Aggiorna driver in Gestione dispositivi.
7. Now, in the Update Driver Software Windows, select “Sfoglia il mio computer per il software del driver."
8. Ora seleziona "Fammi scegliere da un elenco di driver disponibili sul mio computer."
9. Prova a update drivers from the listed versions (make sure to checkmark compatible hardware).
10. If the above didn’t work then go to il sito web del produttore per aggiornare i driver.
11. Download and install the latest driver from the manufacturer’s website then restart your PC.
Method 5: Uninstall Network Adapter Drivers
1. Premi il tasto Windows + R quindi digita “devmgmt.msc"e premi Invio per aprire Gestione dispositivi.
2. Espandi Schede di rete e trova il nome della tua scheda di rete.
3. Assicurati di annotare il nome dell'adattatore nel caso qualcosa vada storto.
4. Right-click on your network adapter and uninstall it.
5. It will ask for confirmation selezionare Sì.
6. Restart your PC and Windows will automatically install the network adapter drivers again.
7. If the drivers are not installed automatically then again open the Device Manager.
8. From the Device Manager menu, click on Action quindi fare clic su "Cerca le modifiche hardware".
Metodo 6: assicurati che Windows sia aggiornato
1. Stampa Tasto Windows + Per aprire Impostazioni, quindi fare clic su Aggiornamento e sicurezza.
2. From the left-hand side, menu click on Windows Update.
3. Ora fai clic su "Controlla aggiornamenti" per verificare la presenza di eventuali aggiornamenti disponibili.
4. If any updates are pending then click on Scarica e installa gli aggiornamenti.
5. Once the updates are downloaded, install them and your Windows will become up-to-date.
6. After the updates are installed reboot your PC to save changes.
Metodo 7: eseguire lo strumento di risoluzione dei problemi della scheda di rete
1. Premi il tasto Windows + I per aprire Impostazioni, quindi fai clic su Aggiornamento e sicurezza.
2. From the left-hand menu select Risoluzione dei problemi.
3. Under Troubleshoot click on Connessioni Internet e quindi fare clic Esegui lo strumento di risoluzione dei problemi.
4. Seguire ulteriori istruzioni visualizzate sullo schermo per eseguire lo strumento di risoluzione dei problemi.
5. If the above didn’t fix the issue then from the Troubleshoot window, click on Scheda di rete e quindi fare clic su Esegui lo strumento di risoluzione dei problemi.
5. Riavvia il PC per salvare le modifiche e vedere se è possibile fix the Network Adapter Missing issue.
Method 8: Install Intel PROSet/Wireless Software
Sometimes the problem is caused due to outdated Intel PROSet Software, hence updating it seems to fix Network Adapter Missing in Windows 10 issue. Perciò, andate qui and download the latest version of PROSet/Wireless Software and install it. This is a third party software which manages your WiFi connection instead of Windows and if PROset/Wireless Software is outdated is can cause drivers issue in Adattatore di rete wireless. Hence, read How to Update Network Adapter Drivers on Windows 10.
Metodo 9: ripristinare la connessione di rete
1. Premi il tasto Windows + I per aprire Impostazioni, quindi fai clic su Rete e Internet.
2. From the left-hand menu select Stato.
3. Now scroll down and click on Ripristino rete in basso.
4. Fare nuovamente clic su "Ripristina ora” under Network reset section.
5. This will successfully reset your network adapter and once it is complete the system will be restarted.
Metodo 10: eseguire un ripristino del sistema
System Restore always works in resolving the error, therefore System Restore can definitely help you in fixing this error. So without wasting any time run system restore in order to resolve Network Adapter Missing issue.
Method 11: Using elevated Command Prompt
1. Premi il tasto Windows + X quindi seleziona Prompt dei comandi (amministratore).
2. Digita il seguente comando in cmd e premi Invio:
netcfg –sn
3. This will display a list of networking protocols and in that list find DNI_DNE.
4. If DNI_DNE is listed then type the following command into cmd:
reg elimina HKCRCLSID {988248f3-a1ad-49bf-9170-676cbbc36ba3} / va / f
netcfg -v -u dni_dne
5. If you don’t see DNI_DNE listed then only run the command netcfg -v -u dni_dne.
6. Now if you receive the error 0x80004002 after trying to run the above command then you need to delete the above key manually.
7. Premi il tasto Windows + R quindi digita regedit e premi Invio.
8. Navigate to the following Registry Key:
HKEY_CLASSES_ROOTCLSID{988248f3-a1ad-49bf-9170-676cbbc36ba3}
9. Delete this key and then again type netcfg -v -u dni_dne command in cmd.
10. Riavvia il PC per salvare le modifiche.
Raccomandato per te:
Questo è tutto, hai avuto successo Fix Network Adapter Missing in Windows 10 ma se hai ancora domande riguardo a questo post, sentiti libero di farle nella sezione commenti.