If you are facing this error, then chances are you may have installed new hardware or software which is causing the issue. Sometimes installing the latest Windows updates seems to cause this issue but you can’t be sure until you troubleshoot the issue. Now as far as software problems are concerned, these might be the possible reasons as to
why you are facing this error:
- Corrupted BCD information
- System File is damaged.
- Loose or faulty SATA/IDE Cable
- Conflicting 3rd party software
- ვირუსი ან მავნე პროგრამა
The error which you will get after a reboot will be:
შეცდომა: Windows failed to start. A recent hardware or software change might have caused the issue after you install Windows Updates
The main problem is that you won’t boot into Windows and you will be stuck at this error message screen. In short, you will be inside a reboot loop as every time you restart your PC you will again face the same error message until you fix the issue. So without wasting any time let’s see how actually to Fix “Windows failed to start. A recent hardware or software change might be the cause” with the below-listed troubleshooting steps.
Fix Windows failed to start. A recent hardware or software change might be the cause.
Method 1: Run Startup/Automatic Repair
1. ჩადეთ Windows 10 ჩამტვირთავი ინსტალაციის DVD ან აღდგენის დისკი და განაახლეთ კომპიუტერი.
2. When prompted to Press any key to boot from CD or DVD, დააჭირეთ ნებისმიერ ღილაკს გაგრძელდება.
3. აირჩიეთ თქვენი ენის პარამეტრები და დააწკაპუნეთ შემდეგი. დააჭირეთ შეკეთებას თქვენი კომპიუტერი ქვედა მარცხენა მხარეს.
4. არჩევის ოფციის ეკრანზე დააწკაპუნეთ პრობლემების მოგვარება.
5. პრობლემების მოგვარების ეკრანზე დააწკაპუნეთ გაფართოებული ვარიანტი.
6. გაფართოებული პარამეტრების ეკრანზე დააწკაპუნეთ ავტომატური შეკეთება ან გაშვების შეკეთება.
7. Wait till the Windows Automatic/Startup Repairs complete.
8. გადატვირთეთ და წარმატებით გააკეთეთ ფიქსის Windows failed to start. A recent hardware or software change might be the cause, if not, continue.
ასევე წაიკითხე: როგორ დავაფიქსიროთ ავტომატური შეკეთება ვერ შეაკეთა თქვენი კომპიუტერი.
Method 2: Boot into Last Known Good Configuration
Before going any further let’s discuss how to Enable Legacy Advanced Boot Menu so that you can easily get Boot Options:
1. Restart your Windows 10.
2. As the system restarts enter into BIOS setup and configure your PC to boot from CD/DVD.
3. ჩადეთ Windows 10 ჩამტვირთავი ინსტალაციის DVD და გადატვირთეთ კომპიუტერი.
4. როცა მოგეთხოვებათ დააჭიროთ ნებისმიერ ღილაკს CD ან DVD-დან ჩასატვირთად, დააჭირეთ ნებისმიერ ღილაკს გასაგრძელებლად.
5. შეარჩიეთ თქვენი language preferences, და დააჭირეთ შემდეგს. დააჭირეთ შეკეთებას თქვენი კომპიუტერი ქვედა მარცხენა მხარეს.
6. არჩევის ოფციის ეკრანზე დააწკაპუნეთ პრობლემების.
7. პრობლემების მოგვარების ეკრანზე დააწკაპუნეთ გაფართოებული ვარიანტი.
8. On Advanced options screen, click სარდლობის სწრაფი.
9. When the Command Prompt(CMD) open type C: და ჩაწერეთ.
10. ახლა ჩაწერეთ შემდეგი ბრძანება:
BCDEDIT /SET {DEFAULT} BoOTMENUPOLICY LEGACY
11. და დააჭირეთ enter to ჩართეთ Legacy Advanced Boot Menu.
12. Close Command Prompt and back on the Choose an option screen, click Continue to restart Windows 10.
13. Finally, don’t forget to eject your Windows 10 installation DVD to get Boot options.
14. On the Boot Options screen, choose “Last Known Good Configuration (Advanced)."
Method 3: Perform a System Restore
1. ჩადეთ Windows-ის საინსტალაციო მედია ან Recovery Drive/System Repair დისკი და აირჩიეთ თქვენი lენობრივი პრეფერენციებიდა დააჭირეთ შემდეგი
2. click რემონტი თქვენი კომპიუტერი ბოლოში.
3. ახლა, აირჩიე პრობლემების და მაშინ Დამატებითი პარამეტრები.
4. ბოლოს დააწკაპუნეთ “სისტემის აღდგენადა მიჰყევით ეკრანზე ინსტრუქციებს აღდგენის დასასრულებლად.
5. Restart your PC to save changes and see if you can fix Windows failed to start. A recent hardware or software change might be the cause error.
მეთოდი 4: გაუშვით SFC და CHKDSK
1. Again go to command prompt using the method 1, click on command prompt in the Advanced options screen.
2. ჩაწერეთ შემდეგი ბრძანება cmd-ში და თითოეულის შემდეგ დააჭირეთ Enter:
sfc /scannow /offbootdir=c: /offwindir=c:windows chkdsk C: /f /r /x
Note: Make sure you use the drive letter where Windows is currently installed. Also in the above command C: is the drive on which we want to check disk, /f stands for a flag which chkdsk the permission to fix any errors associated with the drive, /r let chkdsk search for bad sectors and perform recovery and /x instructs the check disk to dismount the drive before beginning the process.
3. Exit the command prompt and restart your PC.
Method 5: Rebuild BCD configuration
1. Using above method open command prompt using Windows installation disk.
2. Now type the following commands one by one and hit enter after each one:
bootrec.exe /FixMbr bootrec.exe /FixBoot bootrec.exe /RebuildBcd
3. If the above command fails, then enter the following commands in cmd:
bcdedit /export C:BCD_Backup c: cd boot attrib bcd -s -h -r ren c:bootbcd bcd.old bootrec /RebuildBcd
4. Finally, exit the cmd and restart your Windows.
5. This method seems to Fix Windows failed to start. A recent hardware or software change might cause the error, but if it doesn’t work for you, then continue.
Method 6: Set Correct Boot Order
1. When your computer starts (Before the boot screen or the error screen), repeatedly press Delete or F1 or F2 key (Depending upon your computer’s manufacturer) to enter BIOS setup.
2. Once you are in BIOS setup, select the Boot tab from the list of options.
3. Now make sure that the computer მყარი დისკი ან SSD is set as a top priority in the Boot order. If not, use up or down arrow keys to set hard disk at the top, which means the computer will first boot from it rather than any other source.
4. Finally, press F10 to save this change and exit.
რეკომენდებული:
ეს არის ის, რაც თქვენ წარმატებით გაქვთ Fix Windows failed to start. A recent hardware or software change might be the cause, but if you still have any questions regarding this post, please ask them in the comment’s section.