If you are facing this error, then chances are you may have installed new hardware or software which is causing the issue. Sometimes installing the latest Windows updates seems to cause this issue but you can’t be sure until you troubleshoot the issue. Now as far as software problems are concerned, these might be the possible reasons as to
why you are facing this error:
- Corrupted BCD information
- System File is damaged.
- Loose or faulty SATA/IDE Cable
- Conflicting 3rd party software
- Fayras ama furin
The error which you will get after a reboot will be:
Qalad: Windows failed to start. A recent hardware or software change might have caused the issue after you install Windows Updates
The main problem is that you won’t boot into Windows and you will be stuck at this error message screen. In short, you will be inside a reboot loop as every time you restart your PC you will again face the same error message until you fix the issue. So without wasting any time let’s see how actually to Fix “Windows failed to start. A recent hardware or software change might be the cause” with the below-listed troubleshooting steps.
Fix Windows failed to start. A recent hardware or software change might be the cause.
Habka 1: Orod Startup/Automatic Repair
1. Geli Windows 10 DVD-ga rakibaadda bootable ama Disc Recovery iyo inaad dib u bilowdo PC-gaaga.
2. Marka laguu sheego in aad riixdo fure kasta si aad CD ama DVD-ga uga soo saarto. riix furaha kasta sii wadaan.
3. Dooro luuqadaada aad door bidayso, oo taabo Next. Guji Dayactirka kombuyuutarkaaga oo ku yaal dhanka hoose-bidix.
4. Markaad doorato shaashadda ikhtiyaarka ah, dhagsii Dhibaatooyinka Dhibaatada.
5. Shaashadda cillad-bixinta, dhagsii Xulasho horumarsan.
6. Shaashadda Advanced Options, guji Dayactirka Tooska ah ama Dayactirka Bilawga.
7. Sug ilaa inta ay ka dhamaanayso Dayactirka Tooska ah ee Daaqadaha.
8. Dib u bilow oo si guul leh ayaad ku gaadhay Fix Windows failed to start. A recent hardware or software change might be the cause, if not, continue.
Sidoo kale Akhri: Sida loo hagaajiyo Dayactirka Tooska ah ayaa dib u hagaajin kari waayay PC-gaaga.
Method 2: Boot into Last Known Good Configuration
Before going any further let’s discuss how to Enable Legacy Advanced Boot Menu so that you can easily get Boot Options:
1. Restart your Windows 10.
2. As the system restarts enter into BIOS setup and configure your PC to boot from CD/DVD.
3. Geli Windows 10 DVD rakibida bootable oo dib u bilow kombayutarkaga.
4. Marka laguu sheego in aad riixdo fure kasta si aad CD ama DVD-ga uga soo saarto, taabo fure kasta si aad u sii wadato.
5. Xulo adiga dookhyada luqadda, oo guji Next. Guji Dayactirka kombuyuutarkaaga oo ku yaal dhanka hoose-bidix.
6. Markaad doorato shaashadda ikhtiyaarka ah, dhagsii Xallinta Dhibaatada.
7. Shaashadda cillad-bixinta, dhagsii Doorashada horumarsan.
8. Shaashadda sare ee fursadaha, dhagsii Amar Amar.
9. When the Command Prompt(CMD) open type C: iyo garaacaan.
10. Hadda ku qor amarka soo socda:
BCDEDIT/SET {DEFAULT} Dhaxalka BOOTMENUPOLICY
11. And hit enter to Daar Legacy Advanced Boot Menu.
12. Close Command Prompt and back on the Choose an option screen, click Continue to restart Windows 10.
13. Finally, don’t forget to eject your Windows 10 installation DVD to get Boot options.
14. On the Boot Options screen, choose “Last Known Good Configuration (Advanced)."
Habka 3: Samee System Soo Celinta
1. Geli warbaahinta rakibaadda Windows ama Dib u hagaajinta Drive/System Repair Disc oo dooro l kaagadookhyada luqadda, oo guji Next
2. Guji Repair kombuyuutarkaaga xagga hoose.
3. Hadda, dooro Xallinta Dhibaatada ka dibna Fursadaha Horukacsan.
4. Ugu dambeyntii, dhagsii "Nadiifinta Nidaamka” oo raac tilmaamaha shaashadda si aad u dhammaystirto soo celinta.
5. Restart your PC to save changes and see if you can fix Windows failed to start. A recent hardware or software change might be the cause error.
Habka 4: Orod SFC iyo CHKDSK
1. Again go to command prompt using the method 1, click on command prompt in the Advanced options screen.
2. Type the following command in cmd and hit enter after each one:
sfc /scannow /offbootdir=c: /offwindir=c:windows chkdsk C: /f /r /x
Note: Make sure you use the drive letter where Windows is currently installed. Also in the above command C: is the drive on which we want to check disk, /f stands for a flag which chkdsk the permission to fix any errors associated with the drive, /r let chkdsk search for bad sectors and perform recovery and /x instructs the check disk to dismount the drive before beginning the process.
3. Exit the command prompt and restart your PC.
Method 5: Rebuild BCD configuration
1. Using above method open command prompt using Windows installation disk.
2. Now type the following commands one by one and hit enter after each one:
bootrec.exe /FixMbr bootrec.exe /FixBoot bootrec.exe /RebuildBcd
3. If the above command fails, then enter the following commands in cmd:
bcdedit / dhoofinta C:BCD_Backup c: cd boot attrib bcd -s -h -r ren c:bootbcd bcd.old bootrec /RebuildBcd
4. Finally, exit the cmd and restart your Windows.
5. This method seems to Fix Windows failed to start. A recent hardware or software change might cause the error, but if it doesn’t work for you, then continue.
Method 6: Set Correct Boot Order
1. When your computer starts (Before the boot screen or the error screen), repeatedly press Delete or F1 or F2 key (Depending upon your computer’s manufacturer) to geli habaynta BIOS.
2. Once you are in BIOS setup, select the Boot tab from the list of options.
3. Now make sure that the computer Hard disk ama SSD is set as a top priority in the Boot order. If not, use up or down arrow keys to set hard disk at the top, which means the computer will first boot from it rather than any other source.
4. Finally, press F10 to save this change and exit.
lagu talinayo:
Taasi waa waxa aad ku guulaysatay Fix Windows failed to start. A recent hardware or software change might be the cause, but if you still have any questions regarding this post, please ask them in the comment’s section.