If you are facing this error, then chances are you may have installed new hardware or software which is causing the issue. Sometimes installing the latest Windows updates seems to cause this issue but you can’t be sure until you troubleshoot the issue. Now as far as software problems are concerned, these might be the possible reasons as to
why you are facing this error:
- Corrupted BCD information
- System File is damaged.
- Loose or faulty SATA/IDE Cable
- Conflicting 3rd party software
- Вирус или злонамерни софтвер
The error which you will get after a reboot will be:
Грешка: Windows failed to start. A recent hardware or software change might have caused the issue after you install Windows Updates
The main problem is that you won’t boot into Windows and you will be stuck at this error message screen. In short, you will be inside a reboot loop as every time you restart your PC you will again face the same error message until you fix the issue. So without wasting any time let’s see how actually to Fix “Windows failed to start. A recent hardware or software change might be the cause” with the below-listed troubleshooting steps.
Fix Windows failed to start. A recent hardware or software change might be the cause.
Метод 1: Покрените покретање/аутоматску поправку
1. Уметните Виндовс 10 инсталациони ДВД или диск за опоравак и поново покрените рачунар.
2. When prompted to Press any key to boot from CD or DVD, притисните било који тастер да настави.
3. Изаберите своје језичке поставке и кликните на Нект. Кликните на Поправи ваш рачунар у доњем левом углу.
4. На екрану за избор опција кликните Решавање проблема.
5. На екрану Решавање проблема кликните на Напредна опција.
6. На екрану Напредне опције кликните Аутоматска поправка или поправка при покретању.
7. Сачекајте да се заврши поправка Виндовс Аутоматиц/Стартуп Репаирс.
8. Поново покрените и успешно сте Поправити Windows failed to start. A recent hardware or software change might be the cause, ако не, наставите.
Такође читајте: Како да поправите аутоматску поправку која није могла да поправи ваш рачунар.
Method 2: Boot into Last Known Good Configuration
Before going any further let’s discuss how to Enable Legacy Advanced Boot Menu so that you can easily get Boot Options:
1. Restart your Windows 10.
2. As the system restarts enter into BIOS setup and configure your PC to boot from CD/DVD.
3. Уметните Виндовс 10 инсталациони ДВД за покретање и поново покрените рачунар.
4. Када се од вас затражи да притиснете било који тастер за покретање са ЦД-а или ДВД-а, притисните било који тастер да бисте наставили.
5. Изаберите свој језичке преференције, и кликните на Нект. Кликните на Поправи ваш рачунар у доњем левом углу.
6. На екрану за избор опција кликните Решавање проблема.
7. На екрану Решавање проблема кликните на Напредна опција.
8. On Advanced options screen, click командној линији.
9. When the Command Prompt(CMD) open type C: и притисните Ентер.
10. Сада откуцајте следећу команду:
БЦДЕДИТ / СЕТ {ДЕФАУЛТ} БООТМЕНУПОЛИЦИ ЛЕГАЦИ
11. И притисните ентер до Омогући старији напредни мени за покретање.
12. Close Command Prompt and back on the Choose an option screen, click Continue to restart Windows 10.
13. Finally, don’t forget to eject your Windows 10 installation DVD to get Boot options.
14. On the Boot Options screen, choose “Last Known Good Configuration (Advanced)."
Метод 3: Извршите враћање система у претходно стање
1. Ставите Виндовс инсталациони медиј или диск за опоравак/поправку система и изаберите свој лјезичке преференције, и кликните на Нект
КСНУМКС. клик поправка ваш рачунар на дну.
3. Сада одаберите Решавање проблема и онда Напредне опције.
4. На крају кликните на „Опоравак система” и пратите упутства на екрану да бисте довршили враћање.
5. Restart your PC to save changes and see if you can fix Windows failed to start. A recent hardware or software change might be the cause error.
Метод 4: Покрените СФЦ и ЦХКДСК
1. Again go to command prompt using the method 1, click on command prompt in the Advanced options screen.
2. Унесите следећу команду у цмд и притисните ентер после сваке:
sfc /scannow /offbootdir=c: /offwindir=c:windows chkdsk C: /f /r /x
Note: Make sure you use the drive letter where Windows is currently installed. Also in the above command C: is the drive on which we want to check disk, /f stands for a flag which chkdsk the permission to fix any errors associated with the drive, /r let chkdsk search for bad sectors and perform recovery and /x instructs the check disk to dismount the drive before beginning the process.
3. Exit the command prompt and restart your PC.
Method 5: Rebuild BCD configuration
1. Using above method open command prompt using Windows installation disk.
2. Now type the following commands one by one and hit enter after each one:
bootrec.exe /FixMbr bootrec.exe /FixBoot bootrec.exe /RebuildBcd
3. If the above command fails, then enter the following commands in cmd:
бцдедит /екпорт Ц:БЦД_Бацкуп ц: цд боот аттриб бцд -с -х -р рен ц:боотбцд бцд.олд боотрец /РебуилдБцд
4. Finally, exit the cmd and restart your Windows.
5. This method seems to Fix Windows failed to start. A recent hardware or software change might cause the error, but if it doesn’t work for you, then continue.
Method 6: Set Correct Boot Order
1. When your computer starts (Before the boot screen or the error screen), repeatedly press Delete or F1 or F2 key (Depending upon your computer’s manufacturer) to enter BIOS setup.
2. Once you are in BIOS setup, select the Boot tab from the list of options.
3. Now make sure that the computer Хард диск или ССД is set as a top priority in the Boot order. If not, use up or down arrow keys to set hard disk at the top, which means the computer will first boot from it rather than any other source.
4. Finally, press F10 to save this change and exit.
Препоручује се:
То је то што сте успели Fix Windows failed to start. A recent hardware or software change might be the cause, but if you still have any questions regarding this post, please ask them in the comment’s section.