If you are facing this error, then chances are you may have installed new hardware or software which is causing the issue. Sometimes installing the latest Windows updates seems to cause this issue but you can’t be sure until you troubleshoot the issue. Now as far as software problems are concerned, these might be the possible reasons as to
why you are facing this error:
- Corrupted BCD information
- System File is damaged.
- Loose or faulty SATA/IDE Cable
- Conflicting 3rd party software
- Virus atanapi malware
The error which you will get after a reboot will be:
kasalahan: Windows failed to start. A recent hardware or software change might have caused the issue after you install Windows Updates
The main problem is that you won’t boot into Windows and you will be stuck at this error message screen. In short, you will be inside a reboot loop as every time you restart your PC you will again face the same error message until you fix the issue. So without wasting any time let’s see how actually to Fix “Windows failed to start. A recent hardware or software change might be the cause” with the below-listed troubleshooting steps.
Fix Windows failed to start. A recent hardware or software change might be the cause.
Method 1: Run Startup/Automatic Repair
1. Lebetkeun kana Windows 10 instalasi bootable DVD atanapi Pamulihan Disc tur hurungkeun deui PC Anjeun.
2. Lamun dipenta pikeun Pencét kenop nu mana wae nu keur boot ti CD atawa DVD, pencét sagala kenop neruskeun.
3. Pilih preferensi basa anjeun, teras klik Next. Klik ngalereskeun komputer anjeun di kénca handap.
4. Dina milih hiji layar pilihan, klik Troubleshoot.
5. Dina Troubleshoot layar, klik dina Pilihan canggih.
6. Dina layar pilihan Advanced, klik Perbaikan Otomatis atanapi Perbaikan ngamimitian.
7. Wait till the Windows Automatic/Startup Repairs complete.
8. Balikan deui sareng anjeun parantos suksés ngalereskeun Windows failed to start. A recent hardware or software change might be the cause, if not, continue.
Ogé Baca: Kumaha carana ngalereskeun Perbaikan Otomatis henteu tiasa ngalereskeun PC anjeun.
Method 2: Boot into Last Known Good Configuration
Before going any further let’s discuss how to Enable Legacy Advanced Boot Menu so that you can easily get Boot Options:
1. Restart your Windows 10.
2. As the system restarts enter into BIOS setup and configure your PC to boot from CD/DVD.
3. Selapkeun DVD instalasi bootable Windows 10 tur balikan deui PC Anjeun.
4. Lamun dipenta pikeun Pencét kenop nu mana wae nu keur boot ti CD atawa DVD, pencét kenop nu mana wae nu neruskeun.
5. Pilih anjeun karesep basa, teras pencét Teras. Klik ngalereskeun komputer anjeun di kénca handap.
6. Dina milih hiji layar pilihan, klik Troubleshoot.
7. Dina Troubleshoot layar, klik dina Pilihan canggih.
8. Dina layar pilihan Advanced, klik Paréntah ajakan.
9. When the Command Prompt(CMD) open type C: teras pencét énter.
10. Ayeuna ketik paréntah di handap ieu:
BCDEDIT / SET {DEFAULT} WARISAN BOOTMENUPOLICY
11. And hit enter to Aktipkeun Menu Boot Lanjutan Warisan.
12. Close Command Prompt and back on the Choose an option screen, click Continue to restart Windows 10.
13. Finally, don’t forget to eject your Windows 10 installation DVD to get Boot options.
14. On the Boot Options screen, choose “Last Known Good Configuration (Advanced)."
Métode 3: Ngalaksanakeun Pamulihan Sistem
1. Pasang dina média instalasi Windows atawa Pamulihan Girang / System ngalereskeun Disc tur pilih l Anjeunkaresep anguage, teras klik Salajengna
2. Klik ngalereskeun komputer anjeun di handap.
3. Ayeuna, pilih Troubleshoot teras salajengna Pilihan maju.
4. Tungtungna, klik dina "sistim Mulangkeun” sareng turutan pitunjuk dina layar pikeun ngarengsekeun pamulihan.
5. Restart your PC to save changes and see if you can fix Windows failed to start. A recent hardware or software change might be the cause error.
Métode 4: Jalankeun SFC sareng CHKDSK
1. Again go to command prompt using the method 1, click on command prompt in the Advanced options screen.
2. Ketik paréntah di handap ieu dina cmd teras pencét énter saatos masing-masing:
sfc /scannow /offbootdir=c: /offwindir=c:windows chkdsk C: /f /r /x
Note: Make sure you use the drive letter where Windows is currently installed. Also in the above command C: is the drive on which we want to check disk, /f stands for a flag which chkdsk the permission to fix any errors associated with the drive, /r let chkdsk search for bad sectors and perform recovery and /x instructs the check disk to dismount the drive before beginning the process.
3. Exit the command prompt and restart your PC.
Method 5: Rebuild BCD configuration
1. Using above method open command prompt using Windows installation disk.
2. Now type the following commands one by one and hit enter after each one:
bootrec.exe /FixMbr bootrec.exe /FixBoot bootrec.exe /RebuildBcd
3. If the above command fails, then enter the following commands in cmd:
bcdedit / ékspor C: BCD_Backup c: cd boot attrib bcd -s -h -r ren c: bootbcd bcd.old bootrec /RebuildBcd
4. Finally, exit the cmd and restart your Windows.
5. This method seems to Fix Windows failed to start. A recent hardware or software change might cause the error, but if it doesn’t work for you, then continue.
Method 6: Set Correct Boot Order
1. When your computer starts (Before the boot screen or the error screen), repeatedly press Delete or F1 or F2 key (Depending upon your computer’s manufacturer) to asupkeun setelan BIOS.
2. Once you are in BIOS setup, select the Boot tab from the list of options.
3. Now make sure that the computer Hard disk atawa SSD is set as a top priority in the Boot order. If not, use up or down arrow keys to set hard disk at the top, which means the computer will first boot from it rather than any other source.
4. Finally, press F10 to save this change and exit.
disarankeun:
Éta anjeun parantos suksés Fix Windows failed to start. A recent hardware or software change might be the cause, but if you still have any questions regarding this post, please ask them in the comment’s section.