Fix Error code 0x80070035 The network path was not found: In Microsoft Windows sharing the same network allows to access the files and data on each other’s computer without connecting them with the ethernet cable. But sometimes if you are hosting your computer on the network you might see the message saying “Error code: 0x80070035. The network path was not found.”
Well, there are various reason as to why you may be seeing this error code but mainly it is caused due to Antivirus or Firewall blocking the resources. Anyway, without wasting any time let’s see how to actually fix Error code 0x00028001 and error code 0x80070035 The network path was not found with the below-listed troubleshooting guide.
Fix Error code 0x80070035 The network path was not found
确保创建一个还原点,以防出现问题。
方法一:暂时禁用防病毒软件和防火墙
1.右键单击 防病毒程序图标 从系统托盘中选择 禁用。
2.接下来,选择时间范围 防病毒软件将保持禁用状态。
注意:选择尽可能短的时间,例如 15 分钟或 30 分钟。
3.Once done, again check if the error resolves or not.
4.按 Windows 键 + I,然后选择 控制面板。
5.下一步,点击 系统和安全。
6.然后点击 Windows 防火墙。
7. 现在,从左侧窗格中单击“打开或关闭 Windows 防火墙”。
8.选择关闭 Windows 防火墙并重新启动您的电脑。 And see if you’re able to Fix Error code 0x80070035 The network path was not found.
如果上述方法不起作用,请确保按照完全相同的步骤再次打开防火墙。
Method 2: Delete Hidden Network Adapters
1.按Windows键+R然后输入 输入devmgmt.msc 然后按Enter打开 装置经理。
2.现在选择 网络适配器 依次 查看 > 显示隐藏的设备。
3.Right-click on each of the hidden devices and select 卸载设备。
4.Do this for all the hidden devices listed under Network Adapters.
5.重新启动您的电脑以保存更改。
Method 3: Turn ON Network Discovery
1.按 Windows 键 + X,然后选择 控制面板。
2.Now click Network and Internet and then click View network status and tasks.
3.This would take you to Network and Sharing Center, from there click Change Advanced Sharing settings 从左侧菜单。
4.Check mark 开启网络发现 and click Save changes.
5.重新启动您的电脑以保存更改并查看是否能够 Fix Error code 0x80070035 The network path was not found.
Method 4: Enable NetBIOS over TCP/IP
1.按Windows键+R然后输入 ncpa.cpl 并按Enter键。
2.Right-click on your active Wi-Fi or ethernet connection and select 属性。
3.Select 版本4 Internet协议(TCP / IPv4) 并单击属性。
4.现在点击 高级 in the next window and then switch to WINS tab under Advanced TCP/IP Settings.
5.Under NetBIOS setting, check mark “通过TCP / IP启用NetBIOS“, and then click OK.
6.Reboot your PC to save changes
Method 5: Manually enter all PC’s username and password over the network
1.按 Windows 键 + X,然后选择 控制面板。
2.类型 凭据 in the control panel search and click on 凭证管理员。
3.Select Windows凭据 然后点击 Add a Windows credential.
4.One by one type the 用户名和密码 of each machine connected to the network.
5.Follow this on the PC’s connected to the PC and this will Fix Error code 0x80070035 The network path was not found.
1.Right-click on the drive which you want to be shared and select 属性。
2.切换到 共享标签 and if under Network Path it says Not Shared then click on Advanced Sharing button.
3.Check mark “共享该文件夹” and make sure the Share name is correct.
4.单击“应用”,然后单击“确定”。
Method 7: Change Network Security settings
1.按Windows键+R然后输入 输入secpol.msc 并按Enter键。
2.Navigate to the following path under Local Security Policy window:
Local Policies > Security Options > Network security: LAN Manager authentication level
3.双击 网络安全:LAN Manager 身份验证级别 in the right-hand side window.
4.Now from the drop-down, choose Send LM & NTLM-use NTLMv2 session security if negotiated.
5.单击“应用”,然后单击“确定”。
Reboot your PC and after the restart see if you are able to Fix Error code 0x80070035 The network path was not found, if not then continue with the next method.
方法 8:重置 TCP/IP
1.Right-click on Windows Button and select “命令提示符(管理员)。“
2.Now type the following command and press enter after each one:
(a) ipconfig /release
(b) ipconfig /flushdns
(c) ipconfig /renew
3.Again open Admin Command Prompt and type the following and hit enter after each one:
- IPCONFIG / FLUSHDNS的
- nbtstat -r
- netsh的诠释IP复位
- 的netsh winsock重置
4.重新启动以应用更改。
为你推荐:
这样你就成功了 Fix Error code 0x80070035 The network path was not found 但如果您对这篇文章仍有任何疑问,请随时在评论部分提问。