If you are facing this error, then chances are you may have installed new hardware or software which is causing the issue. Sometimes installing the latest Windows updates seems to cause this issue but you can’t be sure until you troubleshoot the issue. Now as far as software problems are concerned, these might be the possible reasons as to
why you are facing this error:
- Corrupted BCD information
- System File is damaged.
- Loose or faulty SATA/IDE Cable
- Conflicting 3rd party software
- ویروس یا بدافزار
The error which you will get after a reboot will be:
خطا: Windows failed to start. A recent hardware or software change might have caused the issue after you install Windows Updates
The main problem is that you won’t boot into Windows and you will be stuck at this error message screen. In short, you will be inside a reboot loop as every time you restart your PC you will again face the same error message until you fix the issue. So without wasting any time let’s see how actually to Fix “Windows failed to start. A recent hardware or software change might be the cause” with the below-listed troubleshooting steps.
Fix Windows failed to start. A recent hardware or software change might be the cause.
Method 1: Run Startup/Automatic Repair
1. وارد کنید DVD یا دیسک بازیابی نصب قابل بوت ویندوز 10 و کامپیوتر خود را مجددا راه اندازی کنید.
2. هنگامی که از شما خواسته شد هر کلیدی را برای بوت شدن از CD یا DVD فشار دهید، هر کلید را فشار دهید به ادامه.
3. تنظیمات زبان خود را انتخاب کنید و روی Next کلیک کنید. روی Repair کلیک کنید کامپیوتر شما در پایین سمت چپ.
4. در صفحه انتخاب گزینه، کلیک کنید عیب یابی
5. در صفحه عیب یابی، روی گزینه پیشرفته
6. در صفحه گزینه های پیشرفته، کلیک کنید تعمیر خودکار یا تعمیر راه اندازی.
7. Wait till the Windows Automatic/Startup Repairs complete.
8. راه اندازی مجدد و شما با موفقیت رفع Windows failed to start. A recent hardware or software change might be the cause, if not, continue.
همچنین خواندن: چگونه تعمیر خودکار را تعمیر کنیم که کامپیوتر شما را تعمیر نمی کند.
Method 2: Boot into Last Known Good Configuration
Before going any further let’s discuss how to Enable Legacy Advanced Boot Menu so that you can easily get Boot Options:
1. Restart your Windows 10.
2. As the system restarts enter into BIOS setup and configure your PC to boot from CD/DVD.
3. DVD نصب قابل بوت ویندوز 10 را وارد کرده و کامپیوتر خود را مجددا راه اندازی کنید.
4. هنگامی که از شما خواسته شد برای بوت شدن از CD یا DVD هر کلیدی را فشار دهید، برای ادامه هر کلید را فشار دهید.
5. خود را انتخاب کنید ترجیحات زبان، و بعد کلیک کنید روی Repair کلیک کنید کامپیوتر شما در پایین سمت چپ.
6. در صفحه انتخاب گزینه، کلیک کنید عیب یابی.
7. در صفحه عیب یابی، روی گزینه پیشرفته.
8. در صفحه گزینه های پیشرفته، کلیک کنید خط فرمان.
9. When the Command Prompt(CMD) open type C: و وارد شوید
10. حالا دستور زیر را تایپ کنید:
BCDEDIT /SET {پیش فرض} BOOTMENUPOLICY LEGACY
11. و enter to را بزنید منوی بوت پیشرفته Legacy را فعال کنید.
12. Close Command Prompt and back on the Choose an option screen, click Continue to restart Windows 10.
13. Finally, don’t forget to eject your Windows 10 installation DVD to get Boot options.
14. On the Boot Options screen, choose “Last Known Good Configuration (Advanced)."
روش 3: بازیابی سیستم را انجام دهید
1. رسانه نصب ویندوز یا دیسک Recovery Drive/System Repair را قرار دهید و l خود را انتخاب کنیدترجیحات زبانیو روی Next کلیک کنید
2. کلیک تعمیر کامپیوتر شما در پایین
3. حالا ، انتخاب کنید عیب یابی و پس از آن گزینه های پیشرفته
4. در نهایت بر روی ” کلیک کنیدبازگرداندن سیستمو دستورالعمل های روی صفحه را برای تکمیل بازیابی دنبال کنید.
5. Restart your PC to save changes and see if you can fix Windows failed to start. A recent hardware or software change might be the cause error.
روش 4: SFC و CHKDSK را اجرا کنید
1. Again go to command prompt using the method 1, click on command prompt in the Advanced options screen.
2. دستور زیر را در cmd تایپ کنید و بعد از هر کدام اینتر را بزنید:
sfc /scannow /offbootdir=c: /offwindir=c:windows chkdsk C: /f /r /x
Note: Make sure you use the drive letter where Windows is currently installed. Also in the above command C: is the drive on which we want to check disk, /f stands for a flag which chkdsk the permission to fix any errors associated with the drive, /r let chkdsk search for bad sectors and perform recovery and /x instructs the check disk to dismount the drive before beginning the process.
3. Exit the command prompt and restart your PC.
Method 5: Rebuild BCD configuration
1. Using above method open command prompt using Windows installation disk.
2. Now type the following commands one by one and hit enter after each one:
bootrec.exe /FixMbr bootrec.exe /FixBoot bootrec.exe /RebuildBcd
3. If the above command fails, then enter the following commands in cmd:
bcdedit /export C:BCD_Backup c: cd boot attrib bcd -s -h -r ren c:bootbcd bcd.old bootrec /RebuildBcd
4. Finally, exit the cmd and restart your Windows.
5. This method seems to Fix Windows failed to start. A recent hardware or software change might cause the error, but if it doesn’t work for you, then continue.
Method 6: Set Correct Boot Order
1. When your computer starts (Before the boot screen or the error screen), repeatedly press Delete or F1 or F2 key (Depending upon your computer’s manufacturer) to enter BIOS setup.
2. Once you are in BIOS setup, select the Boot tab from the list of options.
3. Now make sure that the computer هارد دیسک یا SSD is set as a top priority in the Boot order. If not, use up or down arrow keys to set hard disk at the top, which means the computer will first boot from it rather than any other source.
4. Finally, press F10 to save this change and exit.
توصیه می شود:
این چیزی است که شما با موفقیت انجام داده اید Fix Windows failed to start. A recent hardware or software change might be the cause, but if you still have any questions regarding this post, please ask them in the comment’s section.