If you are facing this error, then chances are you may have installed new hardware or software which is causing the issue. Sometimes installing the latest Windows updates seems to cause this issue but you can’t be sure until you troubleshoot the issue. Now as far as software problems are concerned, these might be the possible reasons as to
why you are facing this error:
- Corrupted BCD information
- System File is damaged.
- Loose or faulty SATA/IDE Cable
- Conflicting 3rd party software
- Virus ou malware
The error which you will get after a reboot will be:
Erreur: Windows failed to start. A recent hardware or software change might have caused the issue after you install Windows Updates
The main problem is that you won’t boot into Windows and you will be stuck at this error message screen. In short, you will be inside a reboot loop as every time you restart your PC you will again face the same error message until you fix the issue. So without wasting any time let’s see how actually to Fix “Windows failed to start. A recent hardware or software change might be the cause” with the below-listed troubleshooting steps.
Fix Windows failed to start. A recent hardware or software change might be the cause.
Méthode 1 : Exécuter le démarrage/réparation automatique
1. Insérez la DVD d'installation amorçable de Windows 10 ou disque de récupération et redémarrez votre PC.
2. Lorsque vous êtes invité à appuyer sur n'importe quelle touche pour démarrer à partir d'un CD ou d'un DVD, appuyez sur n'importe quelle touche continuer.
3. Sélectionnez vos préférences linguistiques et cliquez sur Suivant. Cliquez sur Réparer votre ordinateur en bas à gauche.
4. Sur l'écran de sélection d'une option, cliquez sur Dépanner.
5. Sur l'écran de dépannage, cliquez sur le Options avancées.
6. Sur l'écran Options avancées, cliquez sur Réparation automatique ou réparation de démarrage.
7. Attendez la fin des réparations automatiques/démarrage de Windows.
8. Redémarrez et vous avez réussi Fixer Windows failed to start. A recent hardware or software change might be the cause, if not, continue.
Lisez aussi: Comment réparer la réparation automatique n'a pas pu réparer votre PC.
Method 2: Boot into Last Known Good Configuration
Before going any further let’s discuss how to Enable Legacy Advanced Boot Menu so that you can easily get Boot Options:
1. Restart your Windows 10.
2. As the system restarts enter into BIOS setup and configure your PC to boot from CD/DVD.
3. Insérez le DVD d'installation amorçable de Windows 10 et redémarrez votre PC.
4. Lorsque vous êtes invité à appuyer sur n'importe quelle touche pour démarrer à partir d'un CD ou d'un DVD, appuyez sur n'importe quelle touche pour continuer.
5. Sélectionnez votre préférences linguistiques, et cliquez sur Suivant. Cliquez sur Réparer votre ordinateur en bas à gauche.
6. Sur l'écran de sélection d'une option, cliquez sur Résolution des problèmes.
7. Sur l'écran de dépannage, cliquez sur le Option avancée.
8. Sur l'écran des options avancées, cliquez sur Invite de commandes.
9. When the Command Prompt(CMD) open type C: et appuyez sur Entrée.
10. Tapez maintenant la commande suivante :
BCDEDIT / SET {DEFAULT} BOTMENUPOLICY LEGACY
11. And hit enter to Enable Legacy Advanced Boot Menu.
12. Close Command Prompt and back on the Choose an option screen, click Continue to restart Windows 10.
13. Finally, don’t forget to eject your Windows 10 installation DVD to get Boot options.
14. On the Boot Options screen, choose “Last Known Good Configuration (Advanced). »
Méthode 3 : effectuer une restauration du système
1. Insérez le support d'installation de Windows ou le disque de récupération/disque de réparation du système et sélectionnez votre ordinateur.préférences linguistiques, puis cliquez sur Suivant
2. Cliquez réparation votre ordinateur en bas.
3. Maintenant, choisissez Résolution des problèmes et alors Options avancées.
4. Enfin, cliquez sur «restauration du système" et suivez les instructions à l'écran pour terminer la restauration.
5. Restart your PC to save changes and see if you can fix Windows failed to start. A recent hardware or software change might be the cause error.
Méthode 4 : exécutez SFC et CHKDSK
1. Again go to command prompt using the method 1, click on command prompt in the Advanced options screen.
2. Tapez la commande suivante dans cmd et appuyez sur Entrée après chacune :
sfc /scannow /offbootdir=c: /offwindir=c:windows chkdsk C: /f /r /x
Note: Make sure you use the drive letter where Windows is currently installed. Also in the above command C: is the drive on which we want to check disk, /f stands for a flag which chkdsk the permission to fix any errors associated with the drive, /r let chkdsk search for bad sectors and perform recovery and /x instructs the check disk to dismount the drive before beginning the process.
3. Exit the command prompt and restart your PC.
Method 5: Rebuild BCD configuration
1. Using above method open command prompt using Windows installation disk.
2. Now type the following commands one by one and hit enter after each one:
bootrec.exe /FixMbr bootrec.exe /FixBoot bootrec.exe /RebuildBcd
3. If the above command fails, then enter the following commands in cmd:
bcdedit /export C:BCD_Backup c:attribut de démarrage cd bcd -s -h -r ren c:bootbcd bcd.old bootrec /RebuildBcd
4. Finally, exit the cmd and restart your Windows.
5. This method seems to Fix Windows failed to start. A recent hardware or software change might cause the error, but if it doesn’t work for you, then continue.
Method 6: Set Correct Boot Order
1. When your computer starts (Before the boot screen or the error screen), repeatedly press Delete or F1 or F2 key (Depending upon your computer’s manufacturer) to entrez dans la configuration du BIOS.
2. Once you are in BIOS setup, select the Boot tab from the list of options.
3. Now make sure that the computer Disque dur ou SSD is set as a top priority in the Boot order. If not, use up or down arrow keys to set hard disk at the top, which means the computer will first boot from it rather than any other source.
4. Finally, press F10 to save this change and exit.
Recommandée:
Voilà, vous avez réussi Fix Windows failed to start. A recent hardware or software change might be the cause, but if you still have any questions regarding this post, please ask them in the comment’s section.