If you are facing this error, then chances are you may have installed new hardware or software which is causing the issue. Sometimes installing the latest Windows updates seems to cause this issue but you can’t be sure until you troubleshoot the issue. Now as far as software problems are concerned, these might be the possible reasons as to
why you are facing this error:
- Corrupted BCD information
- System File is damaged.
- Loose or faulty SATA/IDE Cable
- Conflicting 3rd party software
- ウイルスまたはマルウェア
The error which you will get after a reboot will be:
エラー: Windows failed to start. A recent hardware or software change might have caused the issue after you install Windows Updates
The main problem is that you won’t boot into Windows and you will be stuck at this error message screen. In short, you will be inside a reboot loop as every time you restart your PC you will again face the same error message until you fix the issue. So without wasting any time let’s see how actually to Fix “Windows failed to start. A recent hardware or software change might be the cause” with the below-listed troubleshooting steps.
Fix Windows failed to start. A recent hardware or software change might be the cause.
方法 1: スタートアップ/自動修復を実行する
1。 挿入 Windows 10 起動可能なインストール DVD またはリカバリ ディスク PCを再起動してください。
2. CD または DVD からブートするには任意のキーを押すように求めるプロンプトが表示されたら、 任意のキーを押し 続行します。
3. 言語設定を選択し、「次へ」をクリックします。 [修復]をクリックします 左下にあるコンピュータ。
4. On choose an option screen, click トラブルシュート
5. On Troubleshoot screen, click the 高度なオプション。
6. On the Advanced options screen, click 自動修復またはスタートアップ修復。
7. Wait till the Windows Automatic/Startup Repairs complete.
8. Restart and you have successfully 修正する Windows failed to start. A recent hardware or software change might be the cause, if not, continue.
また読む: 自動修復を修正する方法 PC を修復できませんでした。
Method 2: Boot into Last Known Good Configuration
Before going any further let’s discuss how to Enable Legacy Advanced Boot Menu so that you can easily get Boot Options:
1. Restart your Windows 10.
2. As the system restarts enter into BIOS setup and configure your PC to boot from CD/DVD.
3. Windows 10 の起動可能なインストール DVD を挿入し、PC を再起動します。
4. CD または DVD からブートするには任意のキーを押してくださいというプロンプトが表示されたら、任意のキーを押して続行します。
5.を選択します 言語設定、 「次へ」をクリックします。 [修復]をクリックします 左下にあるコンピュータ。
6. On choose an option screen, click 解決します.
7. On Troubleshoot screen, click the 高度なオプション.
8. 詳細オプション画面で、 をクリックします。 コマンドプロンプト.
9. When the Command Prompt(CMD) open type C: Enterキーを押します。
10. 次のコマンドを入力します。
BCDEDIT / SET {DEFAULT} BOOTMENUPOLICY LEGACY
11. Enter キーを押して、 従来のアドバンスト ブート メニューを有効にします。
12. Close Command Prompt and back on the Choose an option screen, click Continue to restart Windows 10.
13. Finally, don’t forget to eject your Windows 10 installation DVD to get Boot options.
14. On the Boot Options screen, choose “Last Known Good Configuration (Advanced).
方法 3: システムの復元を実行する
1. Put in the Windows installation media or Recovery Drive/System Repair Disc and select your l言語設定をクリックし、「次へ」をクリックします
2。 クリック 修理 コンピューターは一番下にあります。
3.ここで、 解決します その後 高度なオプション。
4. 最後に、「システムの復元” and follow on-screen instructions to complete the restore.
5. Restart your PC to save changes and see if you can fix Windows failed to start. A recent hardware or software change might be the cause error.
方法 4: SFC と CHKDSK を実行する
1. Again go to command prompt using the method 1, click on command prompt in the Advanced options screen.
2. cmd に次のコマンドを入力し、各コマンドの後に Enter キーを押します。
sfc /scannow /offbootdir=c: /offwindir=c:windows chkdsk C: /f /r /x
Note: Make sure you use the drive letter where Windows is currently installed. Also in the above command C: is the drive on which we want to check disk, /f stands for a flag which chkdsk the permission to fix any errors associated with the drive, /r let chkdsk search for bad sectors and perform recovery and /x instructs the check disk to dismount the drive before beginning the process.
3. Exit the command prompt and restart your PC.
Method 5: Rebuild BCD configuration
1. Using above method open command prompt using Windows installation disk.
2. Now type the following commands one by one and hit enter after each one:
bootrec.exe /FixMbr bootrec.exe /FixBoot bootrec.exe /RebuildBcd
3. If the above command fails, then enter the following commands in cmd:
bcdedit /export C:BCD_Backup c: cd boot attrib bcd -s -h -r ren c:bootbcd bcd.old bootrec /RebuildBcd
4. Finally, exit the cmd and restart your Windows.
5. This method seems to Fix Windows failed to start. A recent hardware or software change might cause the error, but if it doesn’t work for you, then continue.
Method 6: Set Correct Boot Order
1. When your computer starts (Before the boot screen or the error screen), repeatedly press Delete or F1 or F2 key (Depending upon your computer’s manufacturer) to BIOSセットアップに入ります.
2. Once you are in BIOS setup, select the Boot tab from the list of options.
3. Now make sure that the computer ハードディスクまたは SSD is set as a top priority in the Boot order. If not, use up or down arrow keys to set hard disk at the top, which means the computer will first boot from it rather than any other source.
4. Finally, press F10 to save this change and exit.
推奨:
これで成功です Fix Windows failed to start. A recent hardware or software change might be the cause, but if you still have any questions regarding this post, please ask them in the comment’s section.