If you are facing this error, then chances are you may have installed new hardware or software which is causing the issue. Sometimes installing the latest Windows updates seems to cause this issue but you can’t be sure until you troubleshoot the issue. Now as far as software problems are concerned, these might be the possible reasons as to
why you are facing this error:
- Corrupted BCD information
- System File is damaged.
- Loose or faulty SATA/IDE Cable
- Conflicting 3rd party software
- 病毒或惡意軟件
The error which you will get after a reboot will be:
錯誤: Windows failed to start. A recent hardware or software change might have caused the issue after you install Windows Updates
The main problem is that you won’t boot into Windows and you will be stuck at this error message screen. In short, you will be inside a reboot loop as every time you restart your PC you will again face the same error message until you fix the issue. So without wasting any time let’s see how actually to Fix “Windows failed to start. A recent hardware or software change might be the cause” with the below-listed troubleshooting steps.
Fix Windows failed to start. A recent hardware or software change might be the cause.
方法四:運行啟動/自動修復
1.插入 Windows 10 可啟動安裝 DVD 或復原光碟 並重新啟動您的電腦。
2. 當提示按任意鍵從 CD 或 DVD 啟動時, 按任意鍵 以繼續。
3. 選擇您的語言首選項,然後按一下下一步。 單擊修復 你的電腦在左下角。
4. 在選擇選項畫面上,按一下 故障排除。
5. 在故障排除畫面上,按一下 高級選項。
6. 在「進階選項」畫面上,按一下 自動修復或啟動修復。
7. Wait till the Windows Automatic/Startup Repairs complete.
8.重啟即可成功 固定 Windows failed to start. A recent hardware or software change might be the cause, if not, continue.
相關閱讀: 如何修復“自動修復”無法修復您的電腦。
Method 2: Boot into Last Known Good Configuration
Before going any further let’s discuss how to Enable Legacy Advanced Boot Menu so that you can easily get Boot Options:
1. Restart your Windows 10.
2. As the system restarts enter into BIOS setup and configure your PC to boot from CD/DVD.
3. 插入 Windows 10 可啟動安裝 DVD 並重新啟動電腦。
4. 當提示按任意鍵從 CD 或 DVD 啟動時,按任意鍵繼續。
5.選擇您的 語言偏好, 然後單擊下一步。 單擊修復 你的電腦在左下角。
6. 在選擇選項畫面上,按一下 疑難解答.
7. 在故障排除畫面上,按一下 高級選項.
8. 在進階選項畫面上,按一下 命令提示符.
9. When the Command Prompt(CMD) open type C: 並回車。
10. 現在輸入以下命令:
BCDEDIT / SET {默認} BOOTMENUPOLICY傳統
11.然後按回車鍵 啟用舊版進階啟動選單。
12. Close Command Prompt and back on the Choose an option screen, click Continue to restart Windows 10.
13. Finally, don’t forget to eject your Windows 10 installation DVD to get Boot options.
14. On the Boot Options screen, choose “Last Known Good Configuration (Advanced).“
方法 3:執行系統還原
1. 放入 Windows 安裝媒體或復原磁碟機/系統修復光碟並選擇您的 l語言偏好,然後按一下“下一步”
2。 點擊 修復 您的計算機位於底部。
3.現在,選擇 疑難解答 進而 高級選項。
4. 最後,點擊““系統還原””並按照螢幕上的指示完成恢復。
5. Restart your PC to save changes and see if you can fix Windows failed to start. A recent hardware or software change might be the cause error.
方法 4:運行 SFC 和 CHKDSK
1. Again go to command prompt using the method 1, click on command prompt in the Advanced options screen.
2. 在 cmd 中鍵入以下命令,並在每個命令後按 Enter 鍵:
sfc /scannow /offbootdir=c: /offwindir=c:windows chkdsk C: /f /r /x
Note: Make sure you use the drive letter where Windows is currently installed. Also in the above command C: is the drive on which we want to check disk, /f stands for a flag which chkdsk the permission to fix any errors associated with the drive, /r let chkdsk search for bad sectors and perform recovery and /x instructs the check disk to dismount the drive before beginning the process.
3. Exit the command prompt and restart your PC.
Method 5: Rebuild BCD configuration
1. Using above method open command prompt using Windows installation disk.
2. Now type the following commands one by one and hit enter after each one:
bootrec.exe /FixMbr bootrec.exe /FixBoot bootrec.exe /RebuildBcd
3. If the above command fails, then enter the following commands in cmd:
bcdedit /export C:BCD_Backup c:cd boot attrib bcd -s -h -r ren c:bootbcd bcd.old bootrec /RebuildBcd
4. Finally, exit the cmd and restart your Windows.
5. This method seems to Fix Windows failed to start. A recent hardware or software change might cause the error, but if it doesn’t work for you, then continue.
Method 6: Set Correct Boot Order
1. When your computer starts (Before the boot screen or the error screen), repeatedly press Delete or F1 or F2 key (Depending upon your computer’s manufacturer) to enter BIOS setup.
2. Once you are in BIOS setup, select the Boot tab from the list of options.
3. Now make sure that the computer 硬盤或 SSD is set as a top priority in the Boot order. If not, use up or down arrow keys to set hard disk at the top, which means the computer will first boot from it rather than any other source.
4. Finally, press F10 to save this change and exit.
推薦:
這樣你就成功了 Fix Windows failed to start. A recent hardware or software change might be the cause, but if you still have any questions regarding this post, please ask them in the comment’s section.