How to replace the joystick modules on the DualSense Edge

listed here are the steps on the best way to replace the joystick modules on the DualSense Edge:

Flip off your DualSense Edge controller and disconnect the USB cable if it is connected.
Find the discharge latch on the again of the controller.
With the controller going through proper facet up, push the latch to the facet till the duvet is launched.
Place the duvet to at least one facet.
Find and lift the discharge lever connected to the stick module you want to interchange.
Because the module begins to slip out of its slot, merely pull it out and place it to at least one facet.
We suggest clearing away any mud or particles which can have collected across the stick module earlier than sliding in your substitute.
Now you are prepared to interchange your outdated stick module with a brand new one.
Slide the substitute stick module alongside the grooves of the controller.
Gently press down on the discharge lever.
You’ll hear a click on as soon as the lever locks into place.
Along with your new stick module firmly in its upright and locked place, exchange the entrance cowl by aligning the highest of the duvet with the notches on the controller.
Push it into place till you hear a click on.
If the entrance cowl cannot shut correctly, it is potential the discharge lever hasn’t been secured. Double test it is in its appropriate place earlier than changing the duvet.

Listed here are some extra suggestions:

You should buy substitute stick modules from Sony or from third-party retailers.
Watch out to not harm the joystick modules when eradicating them.
Make sure that the substitute stick modules are appropriate together with your DualSense Edge controller.
In case you are not snug changing the joystick modules your self, you may take your controller to a professional technician.

If you happen to’ve invested in a DualSense Edge controller and need to know the best way to swap out the joystick modules, right here is the whole lot you must know.

The DualSense Edge controller is likely one of the most customisable controllers in the marketplace, and probably the most ‘Professional’ controller that Sony has ever launched.

It comes with a plethora of personalisation choices, with the selection between a number of joystick caps, set off sensitivity and replaceable again buttons. However one of the vital thrilling choices often is the skill to swap out every particular person joystick module and exchange them, negating the necessity to exchange your controller completely if you happen to’re unfortunate sufficient to undergo from joystick drift.

If you happen to’re interested in switching out the joystick modules and need to learn the way, be sure to preserve studying, as we’re going to be breaking it down in just some easy steps.

What you’ll want:

The Brief Model

Flip the controller on its again
Swap the discharge button
Flip the controller over and take away the entrance panel
Gently carry up the joystick levers
Slide the joystick module out
Substitute it
Press the lever down
Put the entrance cowl again on

Step
1

Flip the controller on its again

Flip the controller round to start out the method.
Step
2

Swap the discharge button

There’s a small launch button on the again of the controller. Swap it to launch the entrance panel. It may be somewhat fiddly however you don’t want to use an excessive amount of stress.
Step
3

Flip the controller over and take away the entrance panel

Flip the controller again round so it’s the precise means and take away the entrance panel. It is best to discover that it comes straight off after you have switched the discharge button.
Step
4

Gently carry up the joystick levers

On the facet of every joystick is a silver lever. Gently carry it upwards to launch the joystick module.
Step
5

Slide the joystick module out

As soon as the lever has been raised the joystick module ought to protrude barely from the controller. Merely slide it out in direction of you to take away it.
Step
6

Substitute it

Now you can slide one other joystick module into the controller.
Step
7

Press the lever down

Upon getting changed the joystick module, gently push down the lever to safe it in place.
Step
8

Put the entrance cowl again on

Put the font cowl again on the controller to complete the method. Be sure that the small notches on the high of the duvet line up with the controller.